Welcome to KleenKuip.com's Professional Carpet Cleaners Discussion Forum!

  
Carpet Cleaning Forum Homepage
Forum Home Forum Home > Carpet Cleaners Discussion > Carpet Cleaning Tips and HOW-TO-SECTION
  New Posts New Posts RSS Feed - Jets and Pressure
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Commercial Floor Cleaning Machines

Jets and Pressure

 Post Reply Post Reply
Author
Message
carpetologist View Drop Down
The Great Hardini
The Great Hardini
Avatar
Hocus Pocus

Joined: 20/January/2004
Location: Canada
Status: Offline
Points: 1712
Post Options Post Options   Thanks (0) Thanks(0)   Quote carpetologist Quote  Post ReplyReply Direct Link To This Post Topic: Jets and Pressure
    Posted: 20/October/2004 at 1:46pm

Jets and Pressure

An ongoing debate in the cleaning industry has existed since the beginning of "steam" cleaning concerning the size and number of jets used to apply the cleaning solution to the carpet and the pressure at which it should be applied.

Typical is the "T" jet illustrated. Reading from the left you may find the letters SS indicating a stainless steel jet. Otherwise they are usually brass. The first 2 or 3 numbers will represent the spread angle of the fan jet. The angle 80вк, 90вк, 110вк, etc. plus the height above the carpet will determine the width of the fan when it strikes the pile. As an example, with a 90вк fan (the simplest angle to calculate) the spread of the fan will always be twice the height above the surface. For example, a 90вк jet 5 inches above the carpet will cover a width of 10 inches. The further the jet is from the surface, the wider the fan, and of course, the closer, the narrower the fan. On multiple jets, each jet only covers a fraction of the total width desired.

The next number on the jet is the size of the orifice which determines the amount of solution which can be sprayed at any given pressure. Usually, these go from 02 to 14. They are engineered so that they are cumulatively equal. For example, three #02 jets will equal the output of one #6 jet or two #4 will equal one #8, and so on. The final digit may be a letter E. This means the flow is even across the entire width of the fan. If there is no letter E, the fan will be tapered to allow for the overlap of multiple jets.

The amount of total volume delivered by the jets is expressed in gallon per minute or GPM. For simplicity let's take a single jet wand and vary the pressure. Since a truck mounted unit will need about 1-1/2 GPM to operate efficiently, any variation in pressure results in a need to change jets. For example, at 500 lbs. pressure, we use a #04 jet, at 400 lbs. a #06 jet and at 300 lbs. a #08 jet. The volume remains about the same but the velocity and size of the solution droplets change. This can affect the agitation from the solution pressure and the amount of heat carried to the fibers in the form of droplets. The smaller the jet, the smaller the droplet and the less heat it can carry. Put your wand over a bucket and pull the trigger for 60 seconds. The amount of solution delivered in gallons will be your GPM. Portables should flow at 1-1/4 maximum GPM.

Back to Top
Sponsored Links


Back to Top
billy196628 View Drop Down
Newbie
Newbie
Avatar

Joined: 19/December/2006
Location: United States
Status: Offline
Points: 10
Post Options Post Options   Thanks (0) Thanks(0)   Quote billy196628 Quote  Post ReplyReply Direct Link To This Post Posted: 28/December/2006 at 2:56pm
    ok now we have a blue line thernalwave 2.
the wand it came with has 4 jets size 4 tips now if we go to a size 2 tip will this cause a problem less water per min and less temp .
will a higher presure help I do not mean over 400 psi when we set the presure for carpet .
it,s just after you prespray and clean you are puting so much water in and in the winter thats not a good thing.
summer no problem .
Back to Top
EricValentine View Drop Down
Newbie
Newbie
Avatar

Joined: 30/August/2006
Status: Offline
Points: 20
Post Options Post Options   Thanks (0) Thanks(0)   Quote EricValentine Quote  Post ReplyReply Direct Link To This Post Posted: 28/December/2006 at 7:49pm
Four times the pressure will double the flow.

This was taken from the teejet website's users guide to spray nozzles
If you are in the Las Vegas area, I am always up for lunch. 702-985-6214
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2023 Web Wiz Ltd.

This page was generated in 0.297 seconds.