![]() |
Dwell Time |
Post Reply ![]() |
Page <12 |
Author | |
doug ![]() King of the One Liners ![]() Just My opinion Joined: 31/January/2004 Status: Offline Points: 32711 |
![]() ![]() ![]() ![]() ![]() |
Mr. Steamer: Thats where we differ. We take the time to do it right. Your one pass is what you see is what you get.
![]() |
|
Just My opinion
|
|
![]() |
|
Sponsored Links | |
![]() |
|
MR. STEAMER ![]() True Patriot ![]() Only in the GTA Joined: 03/March/2004 Location: Canada Status: Offline Points: 14549 |
![]() ![]() ![]() ![]() ![]() |
|
|
![]() |
|
Superglide Ken ![]() Grand Potentate ![]() SGK Joined: 17/March/2004 Location: Canada Status: Offline Points: 4868 |
![]() ![]() ![]() ![]() ![]() |
Excellant point on the pre-heat point Doug. Do you know for instance that a hot pre-spray and a cold rinse will clean carpet better than a cold pre-spray and boiling hot water? It is true, and I have tested it both ways to prove that point. Cold is a relative term BTW; in both tests the "cold " water was still around 100 degrees faranhiet. The prespray put down hot really speeds up the emulsication process. Once that is acheived, only warm water is required to remove it from the carpet. That is the main reason the inline sprayer is your freind if you use a TM. If you use a portable, an electric sprayer with very hot solution put down by a .05 jet in a 65 degree pattern serves the same purpose.
Ken Edited by Superglide Ken |
|
Inventor of the Teflon Wand Glide and the Turboteck Rotary Air Duct Cleaners for TMs.
|
|
![]() |
|
doug ![]() King of the One Liners ![]() Just My opinion Joined: 31/January/2004 Status: Offline Points: 32711 |
![]() ![]() ![]() ![]() ![]() |
Other things to keep in mind is. Is the pre spray heated. Is the soiling heavey enough more than one application will be necessary. Will it be necessary to use your groomer to agitate the pre spray to increase it's effectivness. In some instances like in front of furniture or bad traffic areas I pre treat agitate and clean. Then reapply pre spray go about cleaning the rest of the area while your not wasteing time waiting for the prespray. That usually works for us. Sort of cleaning in and out on the heavily soiled areas.
![]() |
|
Just My opinion
|
|
![]() |
|
Superglide Ken ![]() Grand Potentate ![]() SGK Joined: 17/March/2004 Location: Canada Status: Offline Points: 4868 |
![]() ![]() ![]() ![]() ![]() |
Dwell time is dependant on two factors. The first is how long the chemical needs to contact the soils to emulsify them properly. That is usually 15 to 20 minutes. The second factor is the evaporation rate which is fairly constant for all water based liquids at a given humidity level and tempurature. Since in a home cleaning enviroment that is fairly constant too, make sure you clean all areas treated within a 20 to 30 minute window for optimum results.
Ken |
|
Inventor of the Teflon Wand Glide and the Turboteck Rotary Air Duct Cleaners for TMs.
|
|
![]() |
|
surroundings ![]() Journeyman ![]() Joined: 27/June/2004 Location: Australia Status: Offline Points: 243 |
![]() ![]() ![]() ![]() ![]() |
I think that this would be specific to the product, wouldn't it?
My dwell time for my mainstay product is recommended 15 minutes, but
there is no 'maximum' except "Do Not Allow Product To Dry On Carpet"
-Allen |
|
![]() |
|
splash_$$$_dash ![]() Carpet Cleaning Specialist ![]() ![]() Joined: 07/April/2004 Location: Toronto Status: Offline Points: 742 |
![]() ![]() ![]() ![]() ![]() |
what's the average dwell time for the pre-spray you are using? or what is the range you use? minimum to maximum dwell time? |
|
![]() |
Post Reply ![]() |
Page <12 |
Tweet |
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Welcome to KleenKuip.com's Professional Carpet Cleaners Discussion Forum!